Fisher & Paykel · 24-inch category · panel-ready · Held for installer review
Fisher & Paykel DD24DHTI9N cabinet opening requirements
DishwasherFit's record for the Fisher & Paykel DD24DHTI9N gives its cabinet opening requirements and body dimensions from the manufacturer's documents, with the record's status in the lookup. Every figure links to the document it was read from; “Not verified” means no document established it.
Held for installer review. Candidate requires installer review of site conditions, utilities, panel or drawer clearance; do not enable automatic fit from this research batch. The lookup never returns this record as an automatic candidate while the gate stands.
Cabinet opening requirements
| Measurement | Published requirement |
|---|---|
| Minimum opening height | 34 1/4 in |
| Maximum opening height | 36 1/2 in |
| Minimum opening width | 23 5/8 in |
| Maximum opening width | Not verified |
| Minimum opening depth | 22 13/16 in |
| Front clearance | Not verified |
| Corner clearance | Not verified |
Appliance body dimensions
Body dimensions describe the machine, not the hole it needs. They never substitute for the opening requirement above.
| Body measurement | Manufacturer value |
|---|---|
| Height | 34 in |
| Width | 23 9/16 in |
| Depth | 21 25/32 in |
Installation notes from the review
- Body depth is chassis only, excluding custom/pre-finished panels. Cavity depth assumes 3/4-inch panels; surrounding panel gaps and drawer sweep need review.
Published features
- Sound rating
- 43 dBA
- Place settings
- 14
- Racks
- Not verified
- Drying system
- Fan assisted drying
- Annual energy
- 286 kWh/year
- Connectivity
- Smart Appliance
Manufacturer specifications, checked September 20, 2026. Annual energy is a published estimate; sound ratings and drying names are not our test results.
Questions people ask about the DD24DHTI9N
Question wording follows the searches Google runs for this model; the answers come only from the manufacturer documents linked on this page and the lookup's three outcomes.
Fisher Paykel DD24DHTI9N specs dimensions cutout width
The reviewed manufacturer document lists a minimum cabinet opening of 34 1/4 in high, 23 5/8 in wide and 22 13/16 in deep for the Fisher & Paykel DD24DHTI9N, with a maximum opening height of 36 1/2 in. Each figure links to its source in the table on this page. This record is held for installer review, so the lookup never returns it as an automatic candidate.
Is the DD24DHTI9N a standard 24-inch dishwasher?
Fisher & Paykel places the DD24DHTI9N in the 24-inch category. That label describes the cabinet class, not the cutout: the reviewed minimum opening width is 23 5/8 in, and the appliance body is 23 9/16 in wide. Use the opening requirement, never the label, when you compare it with your cabinet.
Will the DD24DHTI9N fit my opening?
Only your measurements can answer that. Enter the opening's height, width and depth in the lookup; the DD24DHTI9N comes back as a dimensional candidate, an installer-review item or outside the published requirements, and because this record is held for installer review it never appears as an automatic candidate. None of the three outcomes is a fit guarantee: mounting, utilities, floor level, trim, panel weight and door swing stay with the installer.
How tall is the DD24DHTI9N, and is that the opening height?
The manufacturer lists the DD24DHTI9N appliance body at 34 in high. The body height is not the opening requirement: the minimum opening height on record is 34 1/4 in and the maximum is 36 1/2 in. Measure from the finished floor to the counter underside at several points and use the smallest reading.
Why is the DD24DHTI9N held for installer review?
It carries a blocking review gate: Candidate requires installer review of site conditions, utilities, panel or drawer clearance; do not enable automatic fit from this research batch. Body depth is chassis only, excluding custom/pre-finished panels. Cavity depth assumes 3/4-inch panels; surrounding panel gaps and drawer sweep need review. The gate stays visible on this page until the evidence resolves.
Manufacturer documents
This is a document-based research record, not a physical installation test or a fit guarantee. Unknowns and source conflicts remain part of the decision.
Check your opening dimensions →
Exact-model retailer links
Resolve the status above before ordering. Confirm stock, delivery, installation service and final cost with the retailer. Links are ordered by retailer name, and commissions never change the dimensional checks.
Installation accessories the manufacturer names
From the Fisher & Paykel installation guide 592795C, checked October 31, 2026. Items marked for one arrangement apply only to it; check what arrives with the dishwasher and what the installer brings before buying anything. Store links are ordered by retailer name.
- Check the supplied installation parts
Included — inspect the delivery Fisher & Paykel lists side and top brackets, sealing tape, screws, a pre-finished toe kick panel, a mounting bracket and cutting template for a custom toe kick, spacer sets and shims.
- Custom drawer panels
Installer to specify This integrated model takes custom drawer panels made to the minimum sizes on page 5. Have the cabinetmaker supply them.
- Supplied power cord; hardwiring optional
Installer to specify The dishwasher comes with a power cord. Hardwiring is optional, needs a qualified electrician and replaces the supplied cord.
- Drain hose extension kit (no part number given)
Only if more drain-hose reach is needed If the supplied hoses do not reach, Fisher & Paykel sells an 11-foot 9 3/4-inch extension kit at fisherpaykel.com. The guide gives no part number, so no product link is shown.
- Confirm drain-hose reach
Needs installer decision No extension is added to this shopping list. Have the installer verify the route.
- Air gap kit, if your code requires one
Installer to specify The guide shows connections through a dual or single air gap kit. Whether one is needed depends on local plumbing code.
Build a printable checklist for your wiring and drain choices
All dishwasher records · How the research works · Corrections or a newer manufacturer drawing? Send us the model and source.