Monogram · 24-inch category · Held for installer review
Monogram ZDT800SSYSS cabinet opening requirements
DishwasherFit's record for the Monogram ZDT800SSYSS gives its cabinet opening requirements and body dimensions from the manufacturer's documents, with the record's status in the lookup. Every figure links to the document it was read from; “Not verified” means no document established it.
Held for installer review. Candidate requires installer review of site conditions, utilities, panel or drawer clearance; do not enable automatic fit from this research batch. The lookup never returns this record as an automatic candidate while the gate stands.
Cabinet opening requirements
| Measurement | Published requirement |
|---|---|
| Minimum opening height | 34 1/2 in |
| Maximum opening height | 35 in |
| Minimum opening width | 24 in |
| Maximum opening width | Not verified |
| Minimum opening depth | 24 in |
| Front clearance | Not verified |
| Corner clearance | Not verified |
Appliance body dimensions
Body dimensions describe the machine, not the hole it needs. They never substitute for the opening requirement above.
Published alternatives
The documents also publish these configurations. The lookup screens on the stricter value; a smaller configuration stays an installer-review result.
- depth from 23 7/8 in — Page 1 cutout diagram minimum cutout depth; the page 2 specifications table’s 24-inch minimum cabinet depth is retained as the conservative reviewed requirement. Source ↗
- height from 33 1/2 in, depth from 23 7/8 in — Flush installation style: 33 1/2 to 34 3/4 inches counter underside to floor per the page 2 flush side view, with 23 7/8-inch minimum cutout width and depth per the page 1 cutout diagram. Flush installation remains installer review only. Source ↗
Installation notes from the review
- Depth uses the page 2 specifications table’s stricter 24-inch minimum cabinet depth; the page 1 cutout diagram separately shows a 23 7/8-inch minimum cutout depth. The smaller figure remains installer review only.
- Standard cutout height is 34 1/2 to 35 inches. The flush-installation views on the same quick specs show 33 1/2 to 34 3/4 inches from counter underside to floor and a 23 7/8-inch minimum cutout width. These are two installation styles, not agreeing measurements; the flush envelope remains installer review only.
- Unit height is adjustable from 33 3/4 to 34 5/8 inches; the recorded body height is the minimum. Adjustable body height is not asserted as a maximum opening height; the recorded maximum is the explicit 35-inch cutout maximum.
- Door clearance is 25 1/2 inches with the door open per the quick specs; that projection is not asserted as a complete minimum front or aisle clearance.
- The manufacturer quick-spec PDF’s internal metadata title reads ZDWR240NBS_QS while the document body names ZDT800SSYSS; values were read from the document body only.
Published features
- Sound rating
- 40 dBA (Normal cycle)
- Place settings
- 16
- Racks
- 3
- Drying system
- Dual Dry System
- Annual energy
- Not verified
- Connectivity
- Yes
Manufacturer specifications, checked September 20, 2026. Annual energy is a published estimate; sound ratings and drying names are not our test results.
Questions people ask about the ZDT800SSYSS
Question wording follows the searches Google runs for this model; the answers come only from the manufacturer documents linked on this page and the lookup's three outcomes.
Monogram ZDT800SSYSS dimensions specs cutout width
The reviewed manufacturer document lists a minimum cabinet opening of 34 1/2 in high, 24 in wide and 24 in deep for the Monogram ZDT800SSYSS, with a maximum opening height of 35 in. Each figure links to its source in the table on this page. This record is held for installer review, so the lookup never returns it as an automatic candidate.
Is the ZDT800SSYSS a standard 24-inch dishwasher?
Monogram places the ZDT800SSYSS in the 24-inch category. That label describes the cabinet class, not the cutout: the reviewed minimum opening width is 24 in, and the appliance body is 23 3/4 in wide. Use the opening requirement, never the label, when you compare it with your cabinet.
Monogram ZDT800SSYSS fit 24 inch cabinet opening
Only your measurements can answer that. Enter the opening's height, width and depth in the lookup; the ZDT800SSYSS comes back as a dimensional candidate, an installer-review item or outside the published requirements, and because this record is held for installer review it never appears as an automatic candidate. None of the three outcomes is a fit guarantee: mounting, utilities, floor level, trim, panel weight and door swing stay with the installer.
How tall is the ZDT800SSYSS, and is that the opening height?
The manufacturer lists the ZDT800SSYSS appliance body at 33 3/4 in high. The body height is not the opening requirement: the minimum opening height on record is 34 1/2 in and the maximum is 35 in. Measure from the finished floor to the counter underside at several points and use the smallest reading.
Why is the ZDT800SSYSS held for installer review?
It carries a blocking review gate: Candidate requires installer review of site conditions, utilities, panel or drawer clearance; do not enable automatic fit from this research batch. Depth uses the page 2 specifications table’s stricter 24-inch minimum cabinet depth; the page 1 cutout diagram separately shows a 23 7/8-inch minimum cutout depth. The smaller figure remains installer review only. Standard cutout height is 34 1/2 to 35 inches. The flush-installation views on the same quick specs show 33 1/2 to 34 3/4 inches from counter underside to floor and a 23 7/8-inch minimum cutout width. These are two installation styles, not agreeing measurements; the flush envelope remains installer review only. Unit height is adjustable from 33 3/4 to 34 5/8 inches; the recorded body height is the minimum. Adjustable body height is not asserted as a maximum opening height; the recorded maximum is the explicit 35-inch cutout maximum. Door clearance is 25 1/2 inches with the door open per the quick specs; that projection is not asserted as a complete minimum front or aisle clearance. The manufacturer quick-spec PDF’s internal metadata title reads ZDWR240NBS_QS while the document body names ZDT800SSYSS; values were read from the document body only. The gate stays visible on this page until the evidence resolves.
Does the ZDT800SSYSS have a smaller published cutout?
Yes. The published drawing also shows a depth from 23 7/8 in. Page 1 cutout diagram minimum cutout depth; the page 2 specifications table’s 24-inch minimum cabinet depth is retained as the conservative reviewed requirement. The lookup screens on the stricter published value; the smaller configuration stays an installer-review result, never an automatic match.
Manufacturer documents
- ZDT800SSYSS manufacturer product page ↗
- ZDT800SSYSS Quick Specs (GE product specification 712025) ↗
- ZDT800SSYSS installation instructions ↗
This is a document-based research record, not a physical installation test or a fit guarantee. Unknowns and source conflicts remain part of the decision.
Check your opening dimensions →
Exact-model retailer links
Resolve the status above before ordering. Confirm stock, delivery, installation service and final cost with the retailer. Links are ordered by retailer name, and commissions never change the dimensional checks.
Installation accessories the manufacturer names
From the Monogram installation instructions, checked October 31, 2026. Items marked for one arrangement apply only to it; check what arrives with the dishwasher and what the installer brings before buying anything. Store links are ordered by retailer name. Links marked affiliate may earn us a commission. As an Amazon Associate I earn from qualifying purchases. Commissions never change this list or the fit checks.
- Check the installation package
Included — inspect the delivery Monogram lists a junction box cover and screw, jumper harness WD21X26318 for converting to hardwiring, a drain hose of about 94 inches with hose clamp, a high drain loop bracket, mounting brackets and screws.
- Handle kit — sold separately
Required purchase Stainless models need one handle kit: ZXADH1STYSS (Statement), ZXADH1MNYSS (Minimalist), ZXADTH1PVB1 (brass) or ZXADTH1PVT1 (titanium). No Amazon listing was found for any of them.
- Power cord kit WX09X70911, only if needed
Plug-in connection only Monogram allows only WX09X70911 (7.9 ft) as a power cord kit. Check whether the delivered unit already has a cord before buying one. Its Amazon listing gives a different length, so it is not linked.
- Use the supplied jumper harness
Permanent wiring only The package includes jumper harness WD21X26318 for converting from a power cord to a hardwired connection. The electrician supplies cable, strain relief and UL-listed wire nuts.
- WD24X10065 12-foot drain hose
Only if more drain-hose reach is needed Only if the supplied hose does not reach. Monogram names this 12-foot service hose, which connects to the drain loop on the unit; total drain-hose length must not exceed 16 feet. A 4-foot hose, WD24X10062, is also listed and not linked here.
- Confirm drain-hose reach
Needs installer decision No extension is added to this shopping list. Have the installer verify the route.
- Hot water line, shut-off valve and 90° elbow
Installer to specify Monogram recommends 3/8-inch copper tubing; for a flexible line it names GE braided hose WX28X326, which has no verified Amazon listing. A 90° elbow with 3/4-inch hose thread and a hand shut-off valve are also listed.
Build a printable checklist for your wiring and drain choices
All dishwasher records · How the research works · Corrections or a newer manufacturer drawing? Send us the model and source.